Associated model numbers: GWKIC, ACSD1G
- Important Information
- WARNING - Moving Door can cause serious injury or death
- DO NOT install transmitter unless the door operator's safety reverse works as required by the door operator's manual
- Wall control must be mounted in sight of door, at least 5 feet above floor and clear of moving door parts
- Keep people clear of opening while door is moving
- DO NOT allow children to play with the transmitter or door operator
- If safety reverse does not work properly:
- Close door then disconnect operator using the manual release handle
- DO NOT use transmitter or door operator
- Refer to Door and Door Operators Owner's Manuals before attempting any repairs
- Electrical Shock can cause serious injury or death:
- Power cord must be unplugged before attaching any wires
- Be sure wire ends do not touch each other or other terminals
- If you have questions or if you need a manual, contact the distributor or manufacturer of the operator
- WARNING - Moving Door can cause serious injury or death
- Installation instructions
- NOTE: program keypad before mounting!
- Features:
- Controls up to three doors
- Panic control – Once control is established and for 30 seconds thereafter, any button will control door
- Two Permanent Personal Identification Numbers (PIN)
- Temporary PIN for special purpose access
- Any PIN can be up to 8 digits long
- Lighted Keypad for ease of use at night
- Indicator Light gives visual confirmation of key presses
- NOTE: For convenience in programming you may wish to install Wireless Keypad after Basic Programming of Wireless Keypad and Garage Door Operator(s) is completed.
- Mount keypad (mounting screws located inside battery compartment
- Slide off battery cover and remove battery
- Mark two holes by tapping a small nail through screw holes on keypad. Drill 1/16' pilot holes then fasten with #6 screws enclosed. Replace Keypad cover.
- Replace battery and slide battery cover back into place
Section 1 - Installation instructions
NOTE: For convenience in programming you may wish to install Wireless Keypad after Basic Programming of Wireless Keypad and Garage Door Operator(s) is completed.- Mount wireless keypad on a flat vertical surface with enough room above to slide cover up. pick location out of path of moving garage door and supporting hardware
- Slide Keypad Cover up and pull off wireless keypad. Slide off battery cover and remove battery
- Mark two holes by tapping a small nail through screw holes on keypad. Drill 1/16' pilot holes then fasten with #6 screws enclosed. Replace Keypad cover.
- Replace battery and slide battery cover back into place
Section 2 - Basic programming
- How to enter Personal Identification Number (PIN 1)
- How to reset the Wireless Keypad memory
Entering PIN 1 | Action | Keypad Indicator |
---|---|---|
Open cover fully | Blinks once and goes out | |
Press 3-5-7 | ||
Press "PROG" | Blinks once each second | |
Enter PIN 1 (up to 8 digits) | ||
Press "PROG" | Double blinks each second | |
Close cover fully |
NOTE: Your wireless Keypad is now ready to signal your Door Operator. Your Door Operator must be programmed to accept the signal from your Wireless Keypad.
Resetting the wireless keypad:- Open cover half way
- Press and hold "PROG" and "8" while fully opening cover
- INDICATOR will blink once and go out
- Close cover fully
NOTE: Wireless Keypad memory is now set the same as when it left the factory (Return to Entering PIN 1).
B - Programming 1 door operatorHow to program your Door Operator to receive the signal from your Wireless Keypad.
WARNING!
During this programming the Door Operator could begin to run. Be sure to stay away from the moving door and it's parts. To prevent the door from moving, close door then disconnect it from the Door Operator by pulling the Red Emergency Release Handle.
Find the Learn Code Button and Radio Signal Indicator located on the Door Operator power head. Open Wireless Keypad Cover fully. This can be found where you see the antenna wire hanging from the motor head (you may have to take the lens cover off). If antenna wire is not hanging from motor head then you have an external receiver which is a black box approx. 6" x 2" mounted somewhere in the garage with a antenna wire hanging from it (pop off cover to find Learn Code Button).
Action | Keypad Indicator |
---|---|
Press Operator Learn Code button | Blinks |
Enter PIN 1 | |
Press "SEND" | Stays on |
Press "SEND" | Goes out |
Press "SEND" to test system | Motor runs |
Press "SEND" to test system | Motor stops |
Use the Emergency Release to reconnect the Door to the Door Operator. Your system is now ready to use.
C - Controlling 1 door operatorAction | Keypad Indicator |
---|---|
Open cover | Wait for Keypad Indicator to go out before pressing any buttons |
Enter PIN 1 | Indicator blinks with each key press |
Press and hold "SEND" | Door moves if only 1 door |
Close cover fully |
NOTE:
- If indicator is solid, PIN 1 was entered correctly
- If indicator blinks, PIN1 was entered incorrectly. Close cover and start over.
- Any Keypad button will control the door within 30 second after door begins to move or until cover is closed
Section 3 - Programming multiple door operators
- How to add Door Operators 2 and 3 to Wireless Keypad
- How to program your door Operator to receive the signal from your Wireless Keypad
WARNING
During this programming the Door Operator could begin to run. Be sure to stay away from the moving door and it's parts. To prevent the door from moving, close door then disconnect it from the Door Operator by pulling the Red Emergency Release Handle.
Action | Keypad Indicator |
---|---|
Open cover fully | Blinks once and goes out |
Enter PIN 1 | |
Press "PROG" | Blinks once each second |
Press "PROG" | Double blinks each second |
Press "PROG" | Triple blinks each second |
Enter total number of doors (2 or 3) | |
Press "PROG" | Goes out |
Close cover fully |
NOTE: Your Wireless Keypad is now ready to signal your door operators. Each Door Operator must be programmed to accept the signal from your Wireless Keypad. Decide which Door Operator will be Door 1, Door 2 and Door 3.
B - Programming multiple door operators- Find the Learn Code Button and Radio Signal Indicator located on the Door Operator power
- Head Open Wireless Keypad cover fully
Action | Radio Signal Indicator |
---|---|
Press Operator Learn Code button | Blinks |
Enter PIN 1 | |
Press "SEND" | |
Enter door number (1, 2, or 3) | Stays on |
Press "SEND" | Goes out |
Press "SEND" to test system | Motor runs |
Press "SEND" to test system | Motor stops |
Close wireless keypad cover fully |
NOTE: Use the Emergency Release to reconnect the Door to the Door Operator. Your system is now ready to use. If you are programming another Door Operator go to that machine and repeat the above steps.
C - Controlling multiple door operatorsAction | Keypad Indicator |
---|---|
Open cover | Wait for keypad indicator to go out before pressing any buttons |
Enter PIN 1 | Indicator blinks with each key press |
Press "SEND" | |
Enter door number (1, 2, or 3) | Door moves |
Close cover fully |
NOTE:
- If indicator is solid, PIN was entered correctly
- If indicator blinks, PIN was entered incorrectly. Close cover and start over.
- Any Keypad Button will control the door within 30 seconds after door begins to move or until cover is closed
Section 4 - Enhanced programming
- How to add a Second Personal Identification Number (PIN2)
- How to change Personal Identification Number (PIN 1 or PIN 2)
- How to add and cancel a Temporary Personal Identification Number (PIN)
Changing a PIN | Action | Keypad Indicator |
---|---|---|
Open cover fully | Blinks once and goes out | |
Enter PIN to be changed | ||
Press "PROG" | Blinks once each second | |
Enter new PIN | ||
Press "PROG" | Double blinks if PIN 1 changed Goes out if PIN 2 changed |
|
Close cover fully |
NOTE: Your Wireless Keypad is now ready to signal your Door Operator(s). Your Door operator(s) must be programmed to accept the signal from your Wireless Keypad.
See 2B Programming 1 Door Operator or 3B Programming Multiple Door Operators.
Adding PIN 2 | Action | Keypad Indicator |
---|---|---|
Open cover fully | Blinks once and goes out | |
Enter 1-5-9 | ||
Press "PROG" | Blinks once each second | |
Enter PIN 2 (up to 8 digits) | ||
Press "PROG" | Goes out | |
Close cover fully |
NOTE: Your Wireless Keypad is now ready to signal your Door Operator(s). Your Door Operator(s) must be programmed to accept the signal from your Wireless Keypad.
See 2B Programming 1 Door Operator or 3B Programming Multiple Door Operators.
Adding Temporary PIN | Action | Keypad Indicator |
---|---|---|
Open cover fully | Blinks once and goes out | |
Enter PIN 1 | ||
Press "PROG" | Blinks once each second | |
Press "PROG" | Double blinks each second | |
Enter temporary PIN | ||
Press "PROG" | Triple blinks each second | |
Close cover fully |
NOTE: Your Wireless Keypad is now ready to signal your Door Operator(s). You do not need to reprogram your Door Operator(s).
Cancelling temporary PIN: The Temporary PIN will remain active until the next time PIN 1 is entered. Entering PIN 1 cancels the Temporary PIN.